UPPF COLOR PPF is the Cobia Colors line: a coloured paint protection film built on the same self-healing TPU base as our clear films, with the colour layer sealed beneath the Platicoat topcoat. It changes the car's finish and protects the paint underneath in a single layer.

Because it is a protective film first, it is heavier and more impact-absorbent than a cosmetic wrap, and the factory paint stays untouched beneath it.

The two products do different jobs. Cast vinyl wrap is a cosmetic finish, usually PVC-based. COLOR PPF is a protective film with a colour finish, built on a self-healing TPU base and run at a heavier gauge than typical wrap vinyl.

In practice that means COLOR PPF absorbs stone chips and swirl marks that vinyl would transmit to the paint underneath, and light scratches in the topcoat close with heat. Vinyl is the cheaper option and comes in a wider range of specialist patterns and textures. If the goal is appearance alone, vinyl does that job; if the goal is appearance plus paint protection, COLOR PPF is the product designed for it.

No, when it is installed and removed by an authorised installer. The adhesive is designed to release cleanly from cured factory paint, and while the film is on the car it shields the paint beneath it.

Two caveats are worth knowing. Paint that has been resprayed or touched up may not be fully cured, or may not bond as well as factory paint, so tell your installer about any previous bodywork. And film left well beyond its service life becomes harder to remove cleanly.

Up to 10 years with regular maintenance, which matches the limited warranty term. Actual service life depends on climate, how the car is stored and washed, and how much direct sun and road debris it takes.

Cars kept outdoors in strong UV and heat sit at the shorter end of that range. Garaged cars washed with a pH-neutral shampoo sit at the longer end.

Three things matter most: wash it regularly with a pH-neutral shampoo and a microfibre mitt, have an authorised installer inspect it once a year, and keep film edges free of trapped grit. A film-safe ceramic coating is optional. It adds gloss and makes cleaning easier, but it is not required for the film to perform or for warranty coverage to apply.

Your installer provides the aftercare instructions specific to the film fitted to your vehicle.

Wait 72 hours after installation before the first wash, so the adhesive can fully cure. After that, hand washing is the recommended method: a pH-neutral car shampoo, two buckets, and a clean microfibre mitt. Touchless automatic washes are acceptable. Avoid brush-type automatic washes, and do not aim a pressure washer directly at film edges.

Yes. UPPF COLOR PPF carries a limited 10-year warranty against manufacturing defects: yellowing, blistering, cracking and delamination.

This is defect coverage. It does not cover damage from road debris and stone chips, accidents, improper washing, chemical or environmental fallout, or installation faults. Coverage requires installation by an authorised installer and registration of the film's roll number. Your installer provides the full written terms at handover.

Damaged COLOR PPF is replaced rather than repaired, and replacement is done panel by panel, so a single damaged panel does not require re-filming the whole vehicle. Light surface scratching in the topcoat self-heals with heat. Cuts, tears and impact damage that reach the adhesive layer need the film on that panel removed and re-applied by an authorised installer.

One limitation to be aware of: replacement film can differ slightly in shade from film that has already spent time on the vehicle, because of production batch variation and weathering. On a highly visible panel, ask your installer whether re-filming the adjacent panels will give a closer match.

Yes. COLOR PPF accepts ceramic coatings that are formulated for use over paint protection film. A coating adds gloss and makes the surface easier to clean. It does not change the film's self-healing behaviour, and it does not alter the warranty terms.

Use a coating your installer confirms is film-safe. Some coatings intended for bare paint contain solvents that can haze a TPU topcoat.

Installation is through an authorised UPPF installer. They will assess the paint condition, confirm the colour against a physical sample rather than a screen, agree the coverage (full car or specific panels), and quote the work.

Ask to see the film on a sample panel before committing. Colour reads differently over different base paints, and a sample against your own car is the only reliable preview.